熱線電話:0571-88538888
                                                        行業資訊當前位置:網站首頁 > 新聞中心
                                                        板框壓濾機有操作要領嗎?

                                                         第一步壓緊:壓濾機操作前須進行整機檢查:查看濾布有無打折或重疊現象,電源是否已正常連接。檢查后即可 進行壓緊操作,首先按一下“啟動”按鈕,油泵開始工作,然后再按一下“壓緊”按鈕,活塞推動壓緊板壓緊,當壓緊力到達調定高點壓力后,液壓系統自動跳停。

                                                         
                                                        First step press: press filter before operation must be checked: check whether there is discount or overlap filter cloth, power supply is normal connection. After checking, the press operation can be carried out. Firstly, press the "start" button, the oil pump starts to work, and then press the "press" button, the piston pushes the pressure plate to press, when the pressure reaches the set point pressure, the hydraulic system automatically stops.
                                                         
                                                        第二步進料:當壓濾機壓緊后,即可進行進料操作:開啟進料泵,并緩慢開啟進料閥門,進料壓力逐漸升高至正常壓力。這時觀察壓濾機出液情況和濾板間的滲漏情況,過濾一段時間后壓濾機出液孔出液量逐漸減少,這時說明濾室內濾渣正在逐漸充滿,當出液口不出液或只有很少量液體時,證明濾室內濾渣已經完全充滿形成濾餅。如需要對濾餅進洗滌或風干操作,即可隨后進行,如不需要洗滌或風干操作即可進行卸餅操作。
                                                         
                                                        Second step feeding: When the filter press is compressed, the feeding operation can be carried out: open the feeding pump, and slowly open the feeding valve, feeding pressure gradually increased to normal pressure. After a period of filtration, the amount of liquid discharged from the outlet hole of the filter reduces gradually, which indicates that the filter residue in the filter chamber is gradually filled. When the outlet of the filter is not liquid or only a small amount of liquid, it proves that the filter residue in the filter chamber has been fully filled to form a cake. If the filter cake needs to be washed or air-dried, it can be carried out subsequently, and unloading operation can be carried out without washing or air-drying operation.
                                                         
                                                        第三步洗滌或風干:壓濾機濾餅充滿后,關停進料泵和進料閥門。開起洗滌泵或空壓機,緩慢開啟進洗液或進風閥門,對濾餅進行洗滌或風干。操作完成后,關閉洗液泵或空壓機及其閥門,即可進行卸餅操作。
                                                         
                                                        The third step is washing or air drying: after the filter cake is filled, the feed pump and the feed valve are shut down. Open the washing pump or air compressor, slowly open the intake liquid or air valve, wash or air-dry the filter cake. After the operation is completed, the lotion pump or air compressor and its valves are closed, and the unloading operation can be carried out.
                                                         
                                                        第四步卸餅:首先關閉進料泵和進料閥門、進洗液或進風裝置和閥門,然后按住操作面板上的“松開”按鈕,活塞桿帶動壓緊板退回,退至合適位置后,放開按住的“松開”按鈕,人工逐塊拉動濾板卸下濾餅,同時清理粘在密封面處的濾渣,防止濾渣夾在密封面上影響密封性能,產生滲漏現象,至此一個操作周期完畢。
                                                         
                                                        Fourth step unloading cake: first close the feed pump and feed valve, wash or air inlet device and valve, and then press the "release" button on the operation panel, the piston rod drive the pressure plate back, back to the appropriate position, release the pressed "release" button, manually pull the filter plate to unload the cake, while cleaning the sticky at the same time The filter residue at the cover prevents the filter residue from clipping on the sealing surface and affecting the sealing performance, resulting in leakage, and the operation cycle is completed.
                                                        美美女免费高清毛片视频,全国三级网站免费观看,一本道无码久道_首页